MANUALS•

General care

Thank you for wearing this UNIMATIC^® watch. It is a precision timepiece manufactured to the highest quality standards, and we hope that it will provide you many years of optimal use. Your UNIMATIC^® watch is unique and individually numbered. Every single reference is Made in Italy. Your watch model reference and serial number are engraved on the case back of the watch. We strongly recommend you purchase genuine UNIMATIC^® products and services safely from our many authorized official online and retail stockists. You can consult our stockists list here:

www.unimaticwatches.com/stockists

Unique ID seal ensures 100% genuine provenience and entitles to 24 months warranty.

Preserve your watch

WATER RESISTANCE:

UNIMATIC^® watches are designed and singularly tested to provide the maximum performances. Before using any watch in water, make sure the crown is screwed in completely and tightly. Do not operate the crown underwater, the same applies to pushers of the Modello Tre chronograph. If used in sea water, rinse the watch in fresh water and dry it completely. Please refer to your model details to check the water resistance specifications.

TEMPERATURE RANGE

Your watch works with stable accuracy in a temperature range of 5°C and 35°C (41°F and 95°F). Do not leave your watch in very low temperatures below -10°C or +14°F for a long period of time since the cold may cause a slight time loss or gain. However, accuracy will be restored once the watch returns at normal temperature.

SHOCKS & VIBRATIONS:

General light activities will not affect your watch, but be careful not to drop your watch or hit it against hard surfaces, as this may cause damage or scratches to the metal surface.

CHEMICALS

Be careful not to expose the watch to solvents, mercury, cosmetic sprays, detergents, adhesives or paints, as the case, bracelet, etc. may become discolored or damaged.

MAGNETISM

Avoid contact with magnets, or putting your watch on top of loudspeakers, refrigerators or magnetic cases for tablets or other electrical devices since such objects generate magnetic fields which could disturb the functions of your watch. Our watches are tested up to 4,800 A/m (approx. 60 gauss).

PROTECTIVE FILM

If your watch has a protective film and/or a sticker on the case back, make sure to peel them off before using your watch. Otherwise, perspiration getting under them may rust the case back.

Movement accuracy

If your watch loses or gains a few seconds per day, you can correct it without an expert aid. The rate of a watch varies slightly depending upon its position. Take it off at night and place it as follows:

To gain a few seconds: Lay the watch flat with the dial uppermost.

To lose a few seconds: Lay the watch vertically with the crown downwards.

To lose more seconds: Lay the watch vertically with the crown uppermost.

Product care

CARE OF CASE AND BRACELET:

To prevent possible rusting of the case and bracelet caused by dust, moisture and perspiration, wipe them periodically with a soft dry cloth. For deep cleaning use a toothbrush with soapy water and dry with a soft cloth.

LEATHER STRAPS:

UNIMATIC^® recommends that you follow the steps below in order to preserve the condition of your leather strap:

– avoid contact with water and dampness to prevent discoloration and deformation;

– avoid prolonged exposure to sunlight to prevent fading;

– do not forget that leather is permeable. Avoid contact with greasy substances and cosmetic products.

SERVICE:

Like any precision instrument, a watch needs regular servicing to ensure that it functions perfectly. We cannot indicate the exact optimal frequency of such work, as it depends entirely on the model, the climate and the owner’s individual care of the watch. However, as a general rule, a watch should be serviced every 4 to 5 years, depending on the conditions in which it is used.

SCREW DOWN CROWN:

All of our watches are fitted with a screw-down crown which must be unscrewed to alter the date and time. After use, push the crown into position 1 then press and screw the crown back down, failure to screw the crown down will compromise water-resistance.

MODELLO UNO

HOW TO SET TIME AND USE THE CROWN:

Your watch is fitted with a screw-down crown which must be unscrewed by turning anti-clockwise before setting time.
After use, push the crown into normal position then press and screw the crown back down: failure to screw the crown down will compromise water-resistance.

1 – Turn clockwise for manual winding
2 –Turn counterclockwise for date setting (if present)
3 – Seconds hand will stop, turn clockwise for time setting

Synchronise the seconds by pushing the crown back to position 2 to coincide with a given time signal.

MODELLO UNO SWISS

HOW TO SET TIME AND USE THE CROWN (MOVEMENT SW200-1):

Your watch is fitted with a screw-down crown, which must be unscrewed by turning anti-clockwise before setting time.
After use, push the crown into normal position then press and screw the crown back down: failure to screw the crown down will compromise water-resistance.

1 – Turn clockwise for manual winding
2 – Turn clockwise for date setting (if present)
3 – Seconds hand will stop, turn counterclockwise for time setting

Synchronise the seconds by pushing the crown back to position 2 to coincide with a given time signal.

HOW TO SET TIME AND USE THE CROWN (MOVEMENT SW200-1 B):

Your watch is fitted with a screw-down crown, which must be unscrewed by turning anti-clockwise before setting time.
This particular movement has no data disk therefore the crown will only have 2 steps when pulled out as shown in the picture above.
After use, push the crown into normal position then press and screw the crown back down: failure to screw the crown down will compromise water-resistance.

1 – Turn clockwise for manual winding
2 – Seconds hand will stop, turn counterclockwise for time setting

Synchronise the seconds by pushing the crown back to position 2 to coincide with a given time signal.

MODELLO UNO GMT

HOW TO SET TIME, GMT FUNCTION AND USE THE CROWN:

Your watch is fitted with a screw-down crown which must be unscrewed by turning anti-clockwise before setting time.
After use, push the crown into normal position then press and screw the crown back down: failure to screw the crown down will compromise water-resistance.

1 – Turn clockwise for manual winding
2 – Date and GMT settings
3 – Seconds hand will stop, turn clockwise for time setting

Synchronise the seconds by pushing the crown back to position 2 to coincide with a given time signal.

THE GLOBAL TIME SCALE CASEBACK:

You can use the global time scale caseback chart to convert between timezones. The internal ring shows the hours differences corresponding to each destination allowing you to easily convert time between locations.

MODELLO UNO CASEBACK

HOW TO USE THE CASEBACK SCALE:

You can use the caseback scale to convert measures in miles, meters, yards, feet, inches.
The values on the connecting lines between units are the numbers of time the smaller unit fits into the larger one. Units are displayed in counter-clockwise order from large to small.

[ MI > M > YD > FT > IN ]

With the caseback scale you can convert any measure simply multiplying or dividing the distance by the number shown between the units.

MODELLO DUE

HOW TO SET TIME AND USE THE CROWN:

Your watch is fitted with a screw-down crown which must be unscrewed by turning anti-clockwise before setting time.
After use, push the crown into normal position then press and screw the crown back down: failure to screw the crown down will compromise water-resistance.

1 – Turn clockwise for manual winding
2 – Date setting (if present)
3 – Seconds hand will stop, turn clockwise for time setting

Synchronise the seconds by pushing the crown back to position 2 to coincide with a given time signal.

Modello Due Swiss

HOW TO SET TIME AND USE THE CROWN:

Your watch is fitted with a screw-down crown which must be unscrewed by turning anti-clockwise before setting time.
After use, push the crown into normal position then press and screw the crown back down: failure to screw the crown down will compromise water-resistance.

1 – Turn clockwise for manual winding
2 – Date setting (if present)
3 – Seconds hand will stop, turn clockwise for time setting

Synchronise the seconds by pushing the crown back to position 2 to coincide with a given time signal.

HOW TO USE THE CASEBACK MILLIRADIAN SCALE:

A milliradian (mrad), is the angle formed when the length of a circular arc equals 1/1000 of the radius of the circle. Since the radian expresses a ratio, it is independent of the units of length used. It is used to approximate to deterimine size and distance with high accuracy.
Given distance or size the scale can be used straightening your arm and covering the target with your fingers once established the ratio you can simply multiply or divide to get either size or distance of any object.

HOW TO SET TIME AND USE THE CROWN (MOVEMENT SW200-1 B):

Your watch is fitted with a screw-down crown, which must be unscrewed by turning anti-clockwise before setting time.
This particular movement has no data disk therefore the crown will only have 2 steps when pulled out as shown in the picture above.
After use, push the crown into normal position then press and screw the crown back down: failure to screw the crown down will compromise water-resistance.

1 – Turn clockwise for manual winding
2 – Seconds hand will stop, turn counterclockwise for time setting

Synchronise the seconds by pushing the crown back to position 2 to coincide with a given time signal.

MODELLO DUE CASEBACK

HOW TO USE THE CASEBACK MILLIRADIAN SCALE:

A milliradian (mrad), is the angle formed when the length of a circular arc equals 1/1000 of the radius of the circle. Since the radian expresses a ratio, it is independent of the units of length used. It is used to approximate to deterimine size and distance with high accuracy.
Given distance or size the scale can be used straightening your arm and covering the target with your fingers once established the ratio you can simply multiply or divide to get either size or distance of any object.

MODELLO TRE

HOW TO SET TIME AND USE THE CROWN:

Your watch is fitted with a screw-down crown which must be unscrewed by turning anti-clockwise before setting time.
After use, push the crown into normal position then press and screw the crown back down: failure to screw the crown down will compromise water-resistance.

1 – Pull out the crown to the second click position.

2 – Turn the crown to set hour and minute hand (Check that AM / PM is set correctly).

3 – Push the crown back into the normal position.

SET THE DATE (if present)

1 – Pull out the crown to the first click position.

2 – Turn the crown clockwise for date setting. (Do not set the date between 9:00PM and 3:00AM, otherwise the day may not change properly. If it is necessary to set the date during that time period, first change the time to any time outside it, set the date and then reset the correct time.)

3 – Push the crown back into the normal position.

HOW TO USE THE CHRONOGRAPH FUNCTION:

A – Start/Stop Pusher [unscrew to use]

B – Reset Hand [unscrew to use]

C – Chronograph seconds hand

D – Chronograph minutes hand

E – 24hrs time sub-dial

STANDARD MEASUREMENT

Unscrew both pushers and press the buttons in the following order : A > A > B

ACCUMULATED ELAPSED TIME MEASUREMENT

Unscrew both pushers and press the buttons in the following order : A > A > A > B

Note: The chronograph can measure up to 60 minutes. The chronograph stops after a measurement for 60 minutes.

MODELLO TRE CASEBACK

THE GLOBAL TIME SCALE CASEBACK:

You can use the global time scale caseback chart to convert between timezones. The external ring shows the hours differences between the different time zones allowing you to convert time between locations.

MODELLO QUATTRO

HOW TO SET TIME AND USE THE CROWN:

Your watch is fitted with a screw-down crown which must be unscrewed by turning anti-clockwise before setting time.
After use, push the crown into normal position then press and screw the crown back down: failure to screw the crown down will compromise water-resistance.

1 – Turn clockwise for manual winding
2 – Date setting (if present)
3 – Seconds hand will stop, turn clockwise for time setting

Synchronise the seconds by pushing the crown back to position 2 to coincide with a given time signal.

MODELLO QUATTRO SWISS

HOW TO SET TIME AND USE THE CROWN (SELLITA SW200 1):

Your watch is fitted with a screw-down crown which must be unscrewed by turning anti-clockwise before setting time.
After use, push the crown into normal position then press and screw the crown back down: failure to screw the crown down will compromise water-resistance.

1 – Turn clockwise for manual winding
2 – Date setting (if present)
3 – Seconds hand will stop, turn clockwise for time setting

Synchronise the seconds by pushing the crown back to position 2 to coincide with a given time signal.

HOW TO SET TIME AND USE THE CROWN (SELLITA SW200-1 B):

Your watch is fitted with a screw-down crown which must be unscrewed by turning anti-clockwise before setting time.
After use, push the crown into normal position then press and screw the crown back down: failure to screw the crown down will compromise water-resistance.

1 – Turn clockwise for manual winding
2 – Date setting (if present)
3 – Seconds hand will stop, turn clockwise for time setting

Synchronise the seconds by pushing the crown back to position 2 to coincide with a given time signal.

MODELLO QUATTRO GMT

HOW TO SET TIME, GMT FUNCTION AND USE THE CROWN:

Your watch is fitted with a screw-down crown which must be unscrewed by turning anti-clockwise before setting time.
After use, push the crown into normal position then press and screw the crown back down: failure to screw the crown down will compromise water-resistance.

1 – Turn clockwise for manual winding
2 – Date and GMT settings
3 – Seconds hand will stop, turn clockwise for time setting

Synchronise the seconds by pushing the crown back to position 2 to coincide with a given time signal.

MODELLO QUATTRO QUARTZ

HOW TO SET TIME AND USE THE CROWN:

Your watch is fitted with a screw-down crown which must be unscrewed by turning anti-clockwise before setting time.
After use, push the crown into normal position then press and screw the crown back down: failure to screw the crown down will compromise water-resistance.

1 – Seconds hand will stop, turn clockwise for time setting

Synchronise the seconds by pushing the crown back to position 2 to coincide with a given time signal.

MODELLO QUATTRO CASEBACK

AIR TO GROUND EMERGENCY CODE SIGNALS

In case of distress, describe the ground to air emergency signal codes on the ground so that the search aircraft or rescue party can easily recognise them. Each letter should be at least 10 m? in size with its top and bottom facing the directions of south and north, respectively. When describing the code on a field of snow, dig a ditch or pile up snow in the form of the letter so that it can be discerned by the shade. If the victim is weakened and does not have enough physical strength to describe the codes on the ground, use clothes or equipments to form the letters. Grass, branches of trees or stones can also serve this purpose.
In rescue operations, the rescue aircraft uses a loudspeaker or a communication tube to send messages to the victim, but it is difficult for the victim to respond to the rescuer. The ground to air emergency signal codes will facilitate communication between them and help rescue operations progress smoothly.

MODELLO CINQUE

HOW TO SET TIME AND USE THE CROWN:

Your watch is fitted with a screw-down crown which must be unscrewed by turning anti-clockwise before setting time.
After use, push the crown into normal position then press and screw the crown back down: failure to screw the crown down will compromise water-resistance.

1 – Turn clockwise for manual winding
2 – Date setting (if present)
3 – Seconds hand will stop, turn clockwise for time setting

Synchronise the seconds by pushing the crown back to position 2 to coincide with a given time signal.

MODELLO CINQUE CASEBACK

THE QUATTRO STAGIONI CASEBACK:

The dates of solstices (summer and winter) and equinoxes (spring and autumn) mark key astronomical events in Earth’s orbit around the Sun. These dates engraved on the caseback provides the wearer with a handy reference to track the changing seasons and celestial events.

UBK BRACELET

The UNIMATIC UBK U solid brushed stainless steel bracelet is compatible with both Modello Uno and Modello Due references.

We strongly advice you to seek out professional assistance from your local watch workshop in any instalments or size adjustment operations of the bracelet since special equipment would be needed. The screws of the links have a thread-locker on the threads to prevent them from unwanted unscrewing. In order to loosen them your local jeweller should warm/heat the bracelet to loosen the thread-locker in that way the screws should come out without any problem. Once done with fitting the bracelet thread-locker should be used to secure the screws and prevent them getting loose due to friction.

By any means don’t try to force the screws, this could lead to permanent damage.

UNIMATIC does not take any responsibility and is not liable for any damage caused using this product.

Below a chart to help you choose the correct product variation for the end links matching your watch.

STRAPS

Straps length chart:

REGISTRATION

Register your watch here:

register.unimaticwatches.com

Use the code written on the unique ID seal to link the watch to your account.

Registration provides a direct check and certification for the genuinity of the watch, helps preventing counterfaits, and enable you to receive a quicker support.

WARRANTY

UNIMATIC watches are entirely designed and assembled in Italy with the finest materials and techniques to ensure the best performance and durability. Every watch is tested and verified before shipment: in the unlikely event of a fault, to obtain warranty service or after sales assistance, please contact us at [email protected]

Your UNIMATIC watch is warranted for a period of twenty-four (24) months, from the date of purchase, under the terms and conditions of this warranty. The international UNIMATIC warranty covers material and manufacturing defects existing at the time of delivery of the purchased UNIMATIC watch (defects). The warranty only comes into force if the warranty card is dated, fully and correctly completed and signed by an official UNIMATIC dealer (valid warranty card). During the warranty period and by presenting the valid warranty card, you will have the right to have any defect repaired free of charge. This manufacturer’s warranty does not cover: normal wear and tear and aging, any damage to any part of the watch resulting from abnormal/ abusive use, lack of care, negligence, accidents (knocks, dents, crushing, broken crystal, etc.), incorrect use of the watch and non-observance of the operating instructions provided (damage caused due to the submersion of the watch with a crown or any of the pushers not fully screwed), watch handled by non-authorised persons (for example for service or repair) or which has been altered in its original condition beyond UNIMATIC’s control. Under no circumstances will UNIMATIC be liable for any indirect or consequential damages of any kind. Any further claim against UNIMATIC, for example for damages additional to the above-described warranty, is expressly excluded. 

The above manufacturer’s warranty is independent of any warranty that may be provided by the seller, for which he carries sole responsibility; does not affect the purchaser’s rights against the seller nor any other mandatory statutory rights the purchaser may have against the seller.

REPAIRS

To request a repair and receive support, please email:

[email protected]

Please try to include pictures or videos to show the problem you’re facing if possible.

RETURNS

If your purchase is not exactly what you are looking for, you have 14 days from receiving your order to arrange your return. To initiate the return, please email: [email protected] . We will provide you with the necessary return form and book the return shipment for you. The cost of a single return is 30EUR.

Please note: You don’t pay the prepaid return cost separately, it is deducted from your refund. By using this returns waybill you consent to the deduction of the return post cost from your refund.

When returning items to us, please ensure they are in “as new” condition, well packaged in their original packaging (carton box, toughcase etc.) and protected. We cannot guarantee full refund in case of damaged returns. Personalized items are made to order and cannot be returned or exchanged. Returns made with an alternative provider will be returned to the sender.

TRY ON:

We understand buying online without trying it on could be tricky sometimes, so here’s our advice to you:
We advise our customer to wrap the watch around their wrist instead of fastened it up. Essentially, once the strap is fully fastened, its worn. All returns that are considered worn will be charged a 2% restocking fee.
For any further enquiries please contact customer service.